SAM9X75 Curiosity Kit

---

SoC Features

The SAM9X7 Series microprocessors are high-performance and cost-optimized Arm926EJ-S CPU-based embedded microprocessors (MPU) running up to 800 MHz. The devices integrate powerful peripherals for connectivity and user interface applications, including MIPI-DSI, LVDS, RGB and 2D graphics, MIPI-CSI-2 camera , Gigabit Ethernet with TSN and CAN-FD. Advanced security functions are offered, such as tamper detection, secure boot, secure key storage, TRNG, PUF as well as high-performance crypto accelerators for AES and SHA. The SAM9X7 Series is supported by Microchip MPLAB®-X development tools, Harmony, Linux® distributions and the Ensemble Graphics Toolkit.

Microchip offers for different supply configurations, fully tested power management solutions respecting the SAM9X7 power sequencing specifications that are referenced in the product specification.

Kit Information

Kit Overview

The SAM9X75-Curiosity documents can be found on microchip website, as following:

Kit Overview

Kit User Guide

Access the console

The usual serial communication parameters are 115200 8-N-1 :

Baud rate 115200 Data 8 bits Parity None Stop 1 bit Flow control None

Access the console on DEBUG serial port

The serial console can be accessed from two connectors. One is from the DEBUG port with the help of a TTL-to-USB serial cable (marked as DEBUG J11), another is from micro-A USB connector that gives access to the on-board serial-to-USB converter (marked as J1 USB_A).

Using DEBUG on TTL-to-USB connector (DEBUG J11)

• For Microsoft Windows users: Install the driver of your USB TTL serial cable. FTDI-based ones are the most popular, have a look to this page to get the driver: http://www.ftdichip.com/Drivers/VCP.htm
• Be sure to connect a 3.3V compatible cable and identify its GND pin. Place it properly according to the silkscreen and connect the cable to the board (J11)
• Make sure the jumpers J14 and J15 are closed on the side marked as DBGU for the UART to work as Debug console.
• For Microsoft Windows users: Identify the USB connection that is established, USB Serial Port should appear in Device Manager. The COMxx number will be used to configure the terminal emulator.
  
   
  • For Linux users: Identify the serial USB connection by monitoring the last lines of dmesg command. The /dev/ttyUSBx number will be used to configure the terminal emulator.

    [605576.562740] usb 1-1.1.2: new full-speed USB device number 17 using ehci-pci
    [605576.660920] usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6001
    [605576.660933] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    [605576.660939] usb 1-1.1.2: Product: TTL232R-3V3
    [605576.660944] usb 1-1.1.2: Manufacturer: FTDI
    [605576.660958] usb 1-1.1.2: SerialNumber: FTGNVZ04
    [605576.663092] ftdi_sio 1-1.1.2:1.0: FTDI USB Serial Device converter detected
    [605576.663120] usb 1-1.1.2: Detected FT232RL
    [605576.663122] usb 1-1.1.2: Number of endpoints 2
    [605576.663124] usb 1-1.1.2: Endpoint 1 MaxPacketSize 64
    [605576.663126] usb 1-1.1.2: Endpoint 2 MaxPacketSize 64
    [605576.663128] usb 1-1.1.2: Setting MaxPacketSize 64
    [605576.663483] usb 1-1.1.2: FTDI USB Serial Device converter now attached to ttyUSB0
    

    A /dev/ttyUSB0 node has been created.
• Now open your favorite terminal emulator with appropriate settings

Demo

Demo archives

Create a SD card with the demo

You need a 1 GB SD card (or more) and to download the image of the demo. The image is compressed to reduce the amount of data to download. This image contains:

• a FAT32 partition with the AT91Bootstrap, U-Boot and the Linux Kernel (zImage and dtb).
• an EXT4 partition for the rootfs.

Multi-platform procedure

To write the compressed image on the SD card, you will have to download and install Etcher. This tool, which is an Open Source software, is useful since it allows to get a compressed image as input. More information and extra help available on the Etcher website.

• Insert your SD card and launch Etcher:

1. Select the demo image. They are marked as "SD Card image" in the demo table above.
   Note that you can select a compressed image (like the demos available here). The tool is able to uncompress files on the fly
2. Select the device corresponding to your SD card (Etcher proposes you the devices that are removable to avoid erasing your system disk)
3. Click on the Flash! button
4. On Linux, Etcher finally asks you to enter your root password because it needs access to the hardware (your SD card reader or USB to SD card converter)
5. then the flashing process begins followed by a verification phase (optional)

• Once writing done, Etcher asks you if you want to burn another demo image:

• Your SD card is ready!

Build From source code

Setup ARM Cross Compiler

• Ubuntu:
  In Ubuntu 22.04 LTS, you can install the ARM Cross Compiler by doing:

  sudo apt-get install gcc-arm-linux-gnueabi
  export CROSS_COMPILE=arm-linux-gnueabi-
     

• Others:
  For others, you can download the ARM cross compiler and setup the environment by doing:

  wget -c https://developer.arm.com/-/media/Files/downloads/gnu/11.2-2022.02/binrel/gcc-arm-11.2-2022.02-x86_64-arm-none-linux-gnueabihf.tar.xz?rev=ffc49e4af4cb4c298c2110a4d887716c&hash=4999788F321A7617C04CA172E31F6B22520741FF
  export CROSS_COMPILE=`pwd`/gcc-arm-11.2-2022.02-x86_64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-
     

Build AT91Bootstrap from sources

This section describes how to get source code from the git repository, how to configure with the default configuration, how to customize AT91Bootstrap based on the default configuration and finally to build AT91Bootstrap to produce the binary. take the default configuration to download U-Boot from NandFlash for example.

Get AT91Bootstrap Source Code

You can easily download AT91Bootstrap source code on the at91bootstrap git repository.

To get the source code, you should clone the repository by doing:

$ git clone https://github.com/linux4sam/at91bootstrap.git
Cloning into 'at91bootstrap'...
remote: Enumerating objects: 17621, done.
remote: Counting objects: 100% (3324/3324), done.
remote: Compressing objects: 100% (1029/1029), done.
remote: Total 17621 (delta 2465), reused 3102 (delta 2285), pack-reused 14297
Receiving objects: 100% (17621/17621), 5.65 MiB | 4.65 MiB/s, done.
Resolving deltas: 100% (13459/13459), done.
$ cd at91bootstrap/

Configure AT91Bootstrap

Assuming you are at the AT91Bootstrap root directory, you will find a configs folder which contains several default configuration files:

sam9x75_curiositynf_uboot_defconfig
sam9x75_curiositysd_uboot_defconfig
sam9x75_curiositydf_qspi_uboot_defconfig

Tips: qspi means to read quad-SPI serial flash, sd means to read mmc card, nf means to read nand flash

You can configure AT91Bootstrap to load U-Boot binary from SD Card by doing:

$ make mrproper
$ make sam9x75_curiositysd_uboot_defconfig

If the configuring process is successful, the .config file can be found at AT91Bootstrap root directory.

Customize AT91Bootstrap

If the default configuration doesn't meet your need, after configuring with the default configuration, you can customize it by doing:

$ make menuconfig

Now, in the menuconfig dialog, you can easily add or remove some features to/from AT91Bootstrap as the same way as kernel configuration.
Move to <Exit> with arrows and press this button hitting the Enter key to exit from this screen.

Build AT91Bootstrap

Then you can build the AT91Bootstrap binary by doing:

$ make

If the building process is successful, the final .bin image is build/binaries/at91bootstrap.bin.

Build U-Boot from sources

Getting U-Boot sources

Dedicated page on U-Boot wiki: http://www.denx.de/wiki/U-Boot/SourceCode

You can easily download U-Boot source code from Linux4SAM GitHub U-Boot repository:

• clone the Linux4sam GitHub U-Boot repository

     $ git clone https://github.com/linux4sam/u-boot-at91.git
     Cloning into 'u-boot-at91'...
     remote: Enumerating objects: 824533, done.
     remote: Counting objects: 100% (71919/71919), done.
     remote: Compressing objects: 100% (15288/15288), done.
     remote: Total 824533 (delta 56145), reused 71765 (delta 56072), pack-reused 752614
     Receiving objects: 100% (824533/824533), 182.52 MiB | 3.67 MiB/s, done.
     Resolving deltas: 100% (677649/677649), done.
     Updating files: 100% (17753/17753), done.
     $ cd u-boot-at91
     

• The source code has been taken from the master branch which is pointing to the latest branch we use. If you want to use the other branch, you can list them and use one of them by doing:

     $ git branch -r
     origin/HEAD -> origin/master
     origin/master
     origin/sam9x60_early
     origin/sam9x60_iar
     origin/sama5d27wlsom1ek_ear
     origin/sama7g5_early
     origin/u-boot-2012.10-at91
     origin/u-boot-2013.07-at91
     origin/u-boot-2014.07-at91
     origin/u-boot-2015.01-at91
     origin/u-boot-2016.01-at91
     origin/u-boot-2016.03-at91
     origin/u-boot-2017.03-at91
     origin/u-boot-2018.07-at91
     origin/u-boot-2019.04-at91
     origin/u-boot-2020.01-at91
     origin/u-boot-2021.04-at91
     origin/u-boot-2022.01-at91
     origin/uboot_5series_1.x
     $ git checkout origin/u-boot-2022.01-at91 -b u-boot-2022.01-at91
     Branch u-boot-2022.01-at91 set up to track remote branch u-boot-2022.01-at91 from origin.
     Switched to a new branch 'u-boot-2022.01-at91'
     

Cross-compiling U-Boot

Before compiling the U-Boot, you need setup cross compile toolchain in the section.

Latest versions of U-boot (2018.07 and newer) have a minimum requirement of 6.0 version of the GCC toolchain. We always recommend to use the latest versions.

Once the AT91 U-Boot sources available, cross-compile U-Boot is made in two steps: configuration and compiling. Check the Configuration chapter in U-Boot reference manual.

Go to the configs/ to find the exact target when invoking make.

The U-Boot environment variables can be stored in different media, above config files can specify where to store the U-Boot environment.

   # To put environment variables in nand flash:
   sam9x75_curiosity_nandflash_defconfig
   # To put environment variables in SD/MMC card:
   sam9x75_curiosity_mmc_defconfig

Here are the building steps for the SAM9X75-Curiosity board:

# You can change the config according to your needs.
make sam9x75_curiosity_mmc_defconfig
make

The result of these operations is a fresh U-Boot binary called u-boot.bin corresponding to the binary ELF file u-boot.

• u-boot.bin is the file you should store on the board
• u-boot is the ELF format binary file you may use to debug U-Boot through a JTag link for instance.

Build Kernel from sources

Required packages

You must install essential host packages on your build host:

• build-essentials
  
• flex
  
• bison
  
• libssl-dev
  
• libncurses5-dev
  
• libncursesw5-dev
  
• ncurses-devel
  

Getting Kernel sources

To get the source code, you have to clone the repository:

$ git clone https://github.com/linux4microchip/linux.git
Cloning into 'linux'...
remote: Enumerating objects: 8587836, done.
remote: Total 8587836 (delta 0), reused 0 (delta 0), pack-reused 8587836
Receiving objects: 100% (8587836/8587836), 3.49 GiB | 13.44 MiB/s, done.
Resolving deltas: 100% (7117887/7117887), done.
Updating files: 100% (70687/70687), done.
$ cd linux

The source code has been taken from the master branch which is pointing on the latest branch we use.

Note that you can also add this Linux4SAM repository as a remote GIT repository to your usual Linux git tree. It will save you a lot of bandwidth and download time:

$ git remote add linux4microchip https://github.com/linux4microchip/linux.git
$ git remote update linux4microchip
Fetching linux4icrochip
From https://github.com/linux4microchip/linux
 * [new branch]                linux-5.10-mchp -> linux4microchip/linux-5.10-mchp
 * [new branch]                linux-5.15-mchp -> linux4microchip/linux-5.15-mchp
 * [new branch]                linux-6.1-mchp -> linux4microchip/linux-6.1-mchp
 * [new branch]                master     -> linux4microchip/master

If you want to use another branch, you can list them and use one of them by doing this:

$ git branch -r
  origin/HEAD -> origin/master
  origin/linux-5.10-mchp
  origin/linux-5.15-mchp
  origin/linux-6.1-mchp
  origin/master
$ git checkout origin/linux-6.1-mchp -b linux-6.1-mchp
Branch linux-6.1-mchp set up to track remote branch linux-6.1-mchp from origin.
Switched to a new branch 'linux-6.1-mchp'

Setup ARM Cross Compiler

• Ubuntu:
  In Ubuntu 22.04 LTS, you can install the ARM Cross Compiler by doing:

  sudo apt-get install gcc-arm-linux-gnueabi
  export CROSS_COMPILE=arm-linux-gnueabi-
     

• Others:
  For others, you can download the ARM cross compiler and setup the environment by doing:

  wget -c https://developer.arm.com/-/media/Files/downloads/gnu/11.2-2022.02/binrel/gcc-arm-11.2-2022.02-x86_64-arm-none-linux-gnueabihf.tar.xz?rev=ffc49e4af4cb4c298c2110a4d887716c&hash=4999788F321A7617C04CA172E31F6B22520741FF
  export CROSS_COMPILE=`pwd`/gcc-arm-11.2-2022.02-x86_64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-
     

Configure and Build the Linux kernel

Now you have to configure the Linux kernel according to your hardware. We have two default configuration at91 SoC in arch/arm/configs

arch/arm/configs/at91_dt_defconfig
arch/arm/configs/sama5_defconfig
arch/arm/configs/sama7_defconfig

• at91_dt_defconfig: for SAM9 (ARM926) series chips
• sama5_defconfig: for SAMA5 series chips
• sama7_defconfig: for SAMA7 series chips

At this step, you can modify default configuration using the menuconfig

$ make ARCH=arm menuconfig

Now, in the menuconfig dialog, you can easily add or remove some features. Once done, Move to <Exit> with arrows and press this button hitting the Enter key to exit from this screen.

Build the Linux kernel image, before you build you need set up the cross compile toolchain, check this section.

$ make ARCH=arm

[..]

  Kernel: arch/arm/boot/Image is ready
  Kernel: arch/arm/boot/zImage is ready

Now you have an usable compressed kernel image zImage.

If you need an uImage you can run this additional step:

make ARCH=arm uImage LOADADDR=0x20008000

[..]

  Kernel: arch/arm/boot/zImage is ready
  UIMAGE  arch/arm/boot/uImage
Image Name:   Linux-6.1.22-linux4microchip-20
Created:      Wed May  4 21:18:58 2022
Image Type:   ARM Linux Kernel Image (uncompressed)
Data Size:    5069704 Bytes = 4950.88 KiB = 4.83 MiB
Load Address: 20008000
Entry Point:  20008000
  Kernel: arch/arm/boot/uImage is ready

make ARCH=arm dtbs

[..]

  DTC     arch/arm/boot/dts/at91-kizbox2-2.dtb
  DTC     arch/arm/boot/dts/at91-kizbox3-hs.dtb
  DTC     arch/arm/boot/dts/at91-nattis-2-natte-2.dtb
  DTC     arch/arm/boot/dts/at91-sama5d27_som1_ek.dtb
  DTC     arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dtb
  DTC     arch/arm/boot/dts/at91-sama5d2_icp.dtb
  DTC     arch/arm/boot/dts/at91-sama5d2_ptc_ek.dtb
  DTC     arch/arm/boot/dts/at91-sama5d2_xplained.dtb
  DTC     arch/arm/boot/dts/at91-sama5d3_xplained.dtb
  DTC     arch/arm/boot/dts/at91-dvk_som60.dtb
  DTC     arch/arm/boot/dts/at91-gatwick.dtb
  DTC     arch/arm/boot/dts/at91-tse850-3.dtb
  DTC     arch/arm/boot/dts/at91-wb50n.dtb
  DTC     arch/arm/boot/dts/sama5d31ek.dtb
  DTC     arch/arm/boot/dts/sama5d33ek.dtb
  DTC     arch/arm/boot/dts/sama5d34ek.dtb
  DTC     arch/arm/boot/dts/sama5d35ek.dtb
  DTC     arch/arm/boot/dts/sama5d36ek.dtb
  DTC     arch/arm/boot/dts/sama5d36ek_cmp.dtb
  DTC     arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dtb
  DTC     arch/arm/boot/dts/at91-sama5d4_xplained.dtb
  DTC     arch/arm/boot/dts/at91-sama5d4ek.dtb
  DTC     arch/arm/boot/dts/at91-vinco.dtb
  DTC     arch/arm/boot/dts/at91-sama7g5ek.dtb
  DTC     arch/arm/boot/dts/at91-sam9x60_curiosity.dtb

[..]

If the building process is successful, the final images can be found under arch/arm/boot/ directory.

Build Yocto/Poky rootfs from sources

Note that building an entire distribution is a long process. It also requires a big amount of free disk space.

The support for Atmel AT91 SoC family is included in a particular Yocto layer: meta-atmel. The source for this layer are hosted on Linux4SAM GitHub account: https://github.com/linux4sam/meta-atmel

Building environment

A step-by-step comprehensive installation is explained in the Yocto Project Quick Build. The following lines have to be considered as an add-on that is AT91 specific or that can facilitate your setup.

Prerequisite

Here are the reference pages for setting up a Yocto building environment: What You Need and How You Get It.

add git-lfs to the package requirement list from whichever Linux distribution you use.

For instance, on Ubuntu or debian, these packages need to be installed on your development host:

sudo apt-get install gawk wget git-core git-lfs diffstat unzip texinfo gcc-multilib \
     build-essential chrpath socat cpio python3 python3-pip python3-pexpect \
     xz-utils debianutils iputils-ping python3-git python3-jinja2 libegl1-mesa libsdl1.2-dev \
     pylint3 xterm

Step by step build procedure

here is a copy of the README procedure available directly in the meta-atmel layer. This file in the meta-atmel layer repository must be considered as the reference and the following copy can be out-of-sync.

starting with Linux4SAM 2021.04 release, the meta-atmel layer supports Yocto templates, so make sure you create a new build environment using oe-init-build-env

This layer provides support for Microchip microprocessors (aka AT91)
====================================================================

For more information about the Microchip MPU product line see:
http://www.microchip.com/design-centers/32-bit-mpus
Linux & Open Source on Microchip microprocessors:
http://www.linux4sam.org


Supported SoCs / MACHINE names
==============================
Note that most of the machine names below, have a SD Card variant that can be
built by adding an "-sd" suffix to the machine name.
- SAMA5D2 product family / sama5d2-xplained, sama5d2-xplained-emmc, sama5d27-som1-ek-sd, sama5d27-som1-ek-optee-sd, sama5d2-ptc-ek, sama5d2-icp, sama5d27-wlsom1-ek-sd
- SAMA5D4 product family / sama5d4ek, sama5d4-xplained
- SAMA5D3 product family / sama5d3xek, sama5d3-xplained
- AT91SAM9x5 product family (AT91SAM9G15, AT91SAM9G25, AT91SAM9X25, AT91SAM9G35 and AT91SAM9X35) / at91sam9x5ek
- AT91SAM9RL / at91sam9rlek
- AT91SAM9G45 / at91sam9m10g45ek
- SAM9X60 / sam9x60ek, sam9x60-curiosity
- SAMA7G5 / sama7g5ek-sd, sama7g5ek-emmc, sama7g5ek-ospi


Sources
=======
- meta-atmel
URI: https://github.com/linux4sam/meta-atmel.git
Branch: kirkstone


Dependencies
============
This Layer depends on :
- poky
URI: https://git.yoctoproject.org/poky
Branch: kirkstone
Tag:yocto-4.0.9

- meta-openembedded
URI: https://git.openembedded.org/meta-openembedded
Branch: kirkstone
Tag/commit:df452d9d98659b49888fa8a5428a0a8bd3e3aaec

- meta-arm (for optee components)
URI: https://git.yoctoproject.org/meta-arm
Branch: kirkstone
Tag:yocto-4.0.1

Build procedure
===============

0/ Create a directory
mkdir my_dir
cd my_dir

1/ Clone yocto/poky git repository with the proper branch ready
git clone https://git.yoctoproject.org/poky && cd poky && \
git checkout -b kirkstone yocto-4.0.9 && cd -

2/ Clone meta-openembedded git repository with the proper branch ready
git clone git://git.openembedded.org/meta-openembedded && \
cd meta-openembedded && git checkout -b kirkstone df452d && cd -

3/ Clone meta-atmel layer with the proper branch ready
git clone https://github.com/linux4sam/meta-atmel.git -b kirkstone

4/ Clone meta-arm layer with the proper branch ready
git clone https://git.yoctoproject.org/meta-arm && cd meta-arm && \
git checkout -b kirkstone yocto-4.0.1 && cd -

5/ Enter the poky directory to configure the build system and start the build process
cd poky
If not created yet, add a new "build-microchip" directory:
mkdir build-microchip
Else, if it's the first time you use Yocto Project templates, and if the
build-microchip directory remains from a previous use, we advise you to start
from a fresh directory. Keep your build-microchip/conf/local.conf file for
reference.

6/ Inside the .templateconf file, you will need to modify the TEMPLATECONF
variable to match the path to the meta-atmel layer "conf" directory:
export TEMPLATECONF=${TEMPLATECONF:-../meta-atmel/conf}

7/ Initialize build directory
source oe-init-build-env build-microchip

8/ To build a small image provided by Yocto Project:
[MACHINE=] bitbake core-image-minimal

Example for sama5d2-xplained-sd SD card image:
MACHINE=sama5d2-xplained-sd bitbake core-image-minimal

9/ To build the microchip image with no graphics support:
[MACHINE=] bitbake microchip-headless-image

Example for sama5d2-xplained-sd SD card image:
MACHINE=sama5d2-xplained-sd bitbake microchip-headless-image

10/ To build the microchip image with graphics support (EGT):
[MACHINE=] bitbake microchip-graphics-image

Example for sama5d2-xplained-sd SD card image:
MACHINE=sama5d2-xplained-sd bitbake microchip-graphics-image

Typical bitbake output
======================
Build Configuration:
BB_VERSION           = "2.0.0"
BUILD_SYS            = "x86_64-linux"
NATIVELSBSTRING      = "universal"
TARGET_SYS           = "arm-poky-linux-gnueabi"
MACHINE              = "sam9x60-curiosity-sd"
DISTRO               = "poky-atmel"
DISTRO_VERSION       = "4.0.9"
TUNE_FEATURES        = "arm armv5 thumb dsp"
TARGET_FPU           = "soft"
meta                 
meta-poky            
meta-yocto-bsp       = "HEAD:09def309f91929f47c6cce386016ccb777bd2cfc"
meta-oe              
meta-networking      
meta-webserver
meta-python
meta-initramfs       = "kirkstone:df452d9d98659b49888fa8a5428a0a8bd3e3aaec"
meta-atmel           = "kirkstone:aeeb0d2e90c6b6546fa5b9cb20bf7e58020e3df9"
meta-multimedia      = "kirkstone:df452d9d98659b49888fa8a5428a0a8bd3e3aaec"
meta-arm
meta-arm-toolchain   = "kirkstone:bafd1d013c2470bcec123ba4eb8232ab879b2660"

Contributing
============
To contribute to this layer you should submit the patches for review to:
the github pull-request facility directly or the forum. Anyway, don't forget to
Cc the maintainers.

Microchip Forum:
https://www.microchip.com/forums/f542.aspx

for some useful guidelines to be followed when submitting patches:
http://www.openembedded.org/wiki/How_to_submit_a_patch_to_OpenEmbedded

Maintainers:
Hari Prasath G E 
Nicolas Ferre 

When creating patches insert the [meta-atmel] tag in the subject, for example
use something like:
git format-patch -s --subject-prefix='meta-atmel][PATCH' 

Recent FAQ

Sam9x75Curiosity

• Using SAMA 5 D 2 ADCDevice: Using the SAMA5D2-compatible ADC device. (Kernel, linux-5.15-mchp, linux-6.1-mchp)
• Crypto Config: How to configure Crypto driver. (Kernel, linux-3.18-at91, linux-4.1-at91, linux-4.4-at91, linux-4.9-at91, linux-4.14-at91, linux-4.19-at91, linux-5.4-at91, linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• USBGadget Config: Configure AT91 USB Gadget on Linux and Endpoint order management (composite USB). (Kernel, linux-4.4-at91, linux-4.9-at91, linux-4.14-at91, linux-4.19-at91, linux-5.4-at91, linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• Pwm Faq: PWM Driver. (Kernel, linux-3.10-at91, linux-3.18-at91, linux-4.1-at91, linux-4.4-at91, linux-4.9-at91, linux-4.14-at91, linux-4.19-at91, linux-5.4-at91, linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• Using Atmel DRMDriver: Using Atmel KMS/DRM LCD driver. (Kernel, linux-3.18-at91, linux-4.1-at91, linux-4.4-at91, linux-4.9-at91, linux-4.14-at91, linux-4.19-at91, linux-5.4-at91, linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• Using Max Touch: Introduction for how to use MaxTouch. (Kernel, linux-3.18-at91, linux-4.1-at91, linux-4.4-at91, linux-4.9-at91, linux-4.14-at91, linux-4.19-at91, linux-5.4-at91, linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• Patching DTin Uboot: How to apply DTBOs in U-boot. (U-Boot, Kernel)
• Using I 2 SC: How to use I2SC. (linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• Media Controller: What is Media controller and how to use it with SAM products.. (linux-5.15-mchp, linux-6.1-mchp)
• ISCWhite Balance Features: White balance features of the Image sensor controller.. (Kernel, linux-4.19-at91, linux-5.4-at91, linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• Sama 7 g 5 Xisc: Detailed explanation of the sama7g5 image acquisition pipeline. (Kernel, linux-5.15-mchp, linux-6.1-mchp)
• Build Issue Buildroot G 1: Buildroot gst1-at91-gstreamer. (BuildRoot)
• External Component On EBI: Connecting an external component on the External Bus Interface. (Kernel, linux-4.14-at91, linux-4.19-at91, linux-5.4-at91, linux-5.10-at91, linux-5.15-mchp, linux-6.1-mchp)
• SDCard Boot Notice: How to boot up the board from SD card. (AT91Bootstrap)
• Hasherrorwhenbooting FITimage: . (U-Boot)
• Using FITwith Overlays: How to use U-boot with FIT image to load overlays. (U-Boot, Kernel)